 |
CircuitWerkes Support
(PDF
manuals and software)
Manuals have a funny
way of walking away just when you need 'em, so
this way you always have our information
available to you. The books are in Adobe Acrobat
PDF format.
This page contains
links to current
production product manuals and software. If you
have an older
CircuitWerkes product, you can find out-of-production
items here .
The following products
are in current production:
- CP-2 - stand alone call
progress decoder for disconnecting any device
auto-answer device or 1A2 key set from a phone
line or PBX
- DC232D-
9600b Serial data
delay for data sync to profanity delays and HD
audio delays. Up to 108 seconds, user
programmable in 100ms increments. .
- DR-10 - dial-up DTMF
operated remote control with audio hybrid and
status inputs. This book is for the latest
version of the DR-10 firmware, which is 1.3.
For older DR-10s, click
here . Manuals Updated 3-06-1999 for
the DR-10a or 8-06-97 for the original
DR-10. A simple DR-10 hookup diagram
can be found on our test
tones page.
- DS-8e - multi digit DTMF
sequence decoder. The older DS-8c book is here.
-
DT-232 - DTMF
to Serial ASCII converter with telephone
autocouplerDTMF Tone Encoder
 DT-232 -
Windows GUI to control and configure DT-232.
CircuitWerkes
assumes no liability for bugs,
though
we would like to hear from you if you find
one. You must have
firmware version
7.00 or higher (released May, 2008) to use the
software.
If
you have version 5 or 6 firmware, please
contact us. If your version is
lower than 5, there is no software support,
but you can contact us about
an inexpensive upgrade for your DT-232 that
will bring it up to date.
If you get an "invalid setup package" or
"setup files corrupt" message when
installing the software, it means that your
web browser didn't completely
download the software. Try right clicking on
the link instead of left clciking
and then choose the "Save As" option.
Depending upon the web browser,
you might have to try the download a couple of
times. Be sure that the
downloaded file is 1.8 (or more) megabytes.
- DTMF-16d/e
- Fully programmable DTMF
tone decoder with 16 outputs.
Decodes sequences and single tones
with multiple output modes. For the earlier
DTMF-16C,
click here.
- EAS-4
- converts contact
closures into serial data for communicating
with the Sage ENDEC. Provides simplified
control for up to four stations equipped with
ENDEC and RP-2 option. A downloadable
Windows-based test program can be used on a
computer with a serial port to test your
EAS-4. Download the program installer from our
test tones page.
- GENr8
- DTMF Tone Encoder
GENr8r
ver 1.3.12 - Windows
GUI to control and configure GENr8.
Version
1.3.12 is for use with version 5.0
firmware. Replaced version 1.3.9.
Older version 1.3.9
is for use with version 4.0 firmware.
Replaced version 1.3.7
which shipped with some recent units but had a
problem uploading config data.
(For version 1.0, download the original
version here)
- HC-3
(formerly AC-3a) -
hybrid telephone autocoupler with balanced
audio. Updated 3-25-98
- HC-3
with ComboLok Option (formerly AC-3A with
ComboLok) - hybrid telephone autocoupler w/
password security. Updated 6-10-03
- MicTel - amplified
Mic/line to telephone interface. The MicTel
has recently been updated and two versions are
available. If your MicTel was made prior to
April of 2006, you probably have MicTelv4.0. If your MicTel was made in April
of 2006 or later, you probably have
MicTel v5.0. Version 4.0 MicTels
have 7 jumpers while Version 5.0 MicTels have
13 jumpers. Use the Configuration Jumper
Locator page of the tech manual to determine
if your MicTel matches your documentation.
. .
-
CircuitWerkes Net
Scanner- Windows GUI
to find CircuitWerkes Web enabled devices on
your network. Will show all pings on your LAN,
reports CircuitWerkes devices by name.
Name reporting only works with CircuitWerkes
devices shipped after 9-1-09. You might need to
run it two or three times in a row to find
everything on your system. It may miss some
devices on the first pass. There is also
a new feature called "scan" If your
Webserver firmware is 1.75 for SentryX or 1.08
for the Sicon-8, the scan function is usually
faster and more robust than the normal "ping"
mode. Scan is very fast and only detects
CircuitWerkes devices. Scan may also detect some
CircuitWerkes devices on other IP address
ranges. Ping detects all
ping-able devices within the specified address
range, but is slower. Windows 7, 8 and
10 users should install the software as the
administrator. Also, when running the
software should run it as the administrator.
.
.
- pREX
- programmable relay
expander
Configuration Manager
- Windows GUI to
control and configure pREX.
This requires installation of Microsoft's .net
version 1.1 framework that can be
found here.
Even if you have a different or newer version
of .net installed,
version 1.1 is required. Install the
.net framework before the pREX software.
After downloading the .zip file, open it
and drag the contents to a new folder and
install (run setup.exe)
from the new folder.
- REX
- relay expander /
multiplier
- SEN-6
- Subaudible 25, 35
& combo 25/35 Hz tone encoder. Provides
filtered, balanced audio in and out.
- SiteSentryX
32-bit_Universal Firmware & Loader
Utility - You
must
use the files and utility software to
upgrade your product. The loader utility
is
the
same for the 32bit versions of the
SiteSentry2, 4 and WAM-2. This zipped
file
contains
firmware for the SiteSentry2,
SiteSentry4 & WAM-2. Choose
the firmware
that matches your hardware. Right click to save!
32
Bit upgrade instructions
- SiteSentryX
8-bit_Firmware Loader Utility - You
must use this tool to
load
the .DFF program files to your product The
loader utility is the same for the
basic non-streaming
versions of the SiteSentry2, 4 and WAM-2.
8-bit Firmware
upgrade Instructions
- Sicon-8 - Dial-up,
recordable, talking remote control with
software client. There is also a Quick
Start guide for users that want
simple instructions on how
to connect the Sicontroller
software to the Sicon-8.
Sicontroller
Software - Windows GUI to
control & configure the
Sicon-8.
Script
Examples for
the Sicontroller Software. Perform complex
(intelligent) operations using the Sicon-8
combined with the Sicontroller
software.
Sicon-8
Firmware - Upgrades the main
firmware via a bootloader.
Sicon-8
Webserver32 Instructions -
Technical addendum to the Sicon-8
manual for the new 32 bit Webserver
hardware.
Sicon-8
Webserver32 Firmware
- Latest firmware for the 32bit
(graphical
meters) version of the Sicon-8 Webserver.
Requires
main FW of 1.75 or higher.
Sicon-8
Default Event Scheduler
with 4 hour hardware logging
Sicon-8
USB Update - Upgrades the USB
firmware also a driver
D/L link.
- Silence Sentinal - DISCONTINUED:
Replaced by the WAM-2 - Web enabled 2 channel
audio monitor with silence & overload
detection and six, user controlled, relay
outputs with automatic operation.
Silence
Sentinal -
Multi-Site Monitoring,
control and configuration -
manager software for the
Silence Sentinal.
Older WebSS
Software:(includes the technical
manuals, too).
WebSSMulti_1_3_15_Setup.exe
is for WebSS FW 1.7-Alpha
WebSSMulti_1_3_10_Setup.exe works with
firmware version 1.4 and older
SiteSentry2 - Web
enabled 2 channel site remote control
& monitor with stereo audio
silence & overload detection and
six, user controlled, relay outputs
with automatic operation. Has a
streaming audio option.
SiteSentry2
8-bit Firmware - Upgrades the main
firmware and
user
interface for
8-bit (non-streaming) units. (released
08-01-2014)
Note: Not for
SiteSentry2 version 1.xx units.
Includes the 8-bit FW
Loader Utility.
SiteSentry2 (32-bit)
Universal Firmware
32
Bit upgrade instructions
*******************
Older SiteSentry2 ***********************
- SiteSentry2 version 1.xx -Older version of the
Web enabled 2 channel site remote control
& monitor with audio silence &
overload detection and six, user controlled,
relay outputs with automatic operation.
SiteSentry2 (version 1.15) - Multi-Site
Monitoring, control and
configuration manager software for the
SiteSentry2 version 1.xx.
Does
not work with version 2.xx boards.
*************************************************************************
- SiteSentry4 - Web enabled
4channel site remote control &
monitor with stereo audio silence &
overload detection and six, user
controlled, relay outputs with automatic
operation. Has a streaming audio option.
SiteSentry4
non-streaming Firmware
-Upgrades the
main firmware and user interface for
8-bit (non-streaming)
units.(v1.5.9, released
08-01-2014) 8-bit
Firmware upgrade Instructions
Includes the 8-bit
FW Loader Utility.
SiteSentry4 (32-bit)
Universal Firmware
32
Bit upgrade instructions
- SUB-03f
- In 2003, the SUB-03
series was completely redesigned and is a
major improvement over all previous decoders.
Using high stability filters and
microprocessor based tone detection and
control, these units boast superior noise
immunity, faster response times, fewer
detection errors, and a broader detection
range than any other decoder. They are quick
to install and reliable in operation. Older
version manuals can be found in the obsolete manuals
section of this site.
- TAC-5 -
dial-up DTMF operated remote control with
audio hybrid and one status input. TheTAC-5 is
similar to the DR-10 in function, but with
fewer relays and at a lower cost. The TAC-5
also has some updated features not found on
the DR-10.
-
Telco-6 - Multi-line
telephone ring detector with relay outputs
-
TelTap - Manual
telephone coupler and monitor
-
Temperature Sensor - External
temperature board for Sicon-8 and
SiteSentry2.
- Transcon-16
- Bi-directional
contact closure transporter
- WAM-2 - Web enabled 2
channel audio monitor with silence &
overload detection and six, user controlled,
relay outputs with automatic operation.
(Replaces/updates the Silence Sentinal). Has a
streaming audio option.
WAM-2
8-bit Firmware - Upgrades the main
firmware and user
interface
for 8-bit (non-streaming) units. released
08-01-2014
Includes
the 8-bit FW Loader Utility.
WAM-2 32-bit) Universal
Firmware
32
Bit upgrade instructions
These manuals have
generally printed amazingly well on a variety of
printers, however, they are not absolutely
guaranteed to print faithfully on every type of
printer. If the printed output doesn't look like
what you see on your screen, try a different
printer or printer driver.
If you are looking for manuals
for discontinued Gentner products,
please click
here.
Please
note that we do not sell or service Gentner
products. The few links here are provided as a
courtesy to former Gentner product users who are
seeking technical documents for their products.
Test Tones, programs
and hookup information - for your
convenience, you can download DTMF and
subaudible tones for testing various
CircuitWerkes products. Additional test tools
and diagrams can also be found here.
Contact Us
- if you don't see a
manual listed that you need, or you discover any
problems with any manuals, send e-mail to our
support staff and we'll take care of it for you.
|
